Viking HID-2 Dokumentacja Pobierz pdf (Strona 6)

E. Privacy Number

The “Privacy Number” is factory disabled so an entry phone off-hook will automatically ring the house phones. If a “Privacy Number”

is programmed, the visitor must Touch Tone dial the number to be able to call into the house. The “Privacy Number” may be from 1

to 6 digits and is stored in location “#00”. To disable the “Privacy Number,” clear the number’s memory location by entering “#00”

without any previous digits.

F. Keyless Entry Codes and One Time Use Keyless Entry Codes

Each entry phone may have a combination of up to 6 keyless entry codes or one time use keyless entry codes for Touch Tone key-

less entry. The keyless entry codes may be from 4 to 6 digits in length and are stored in locations #11 - #16 for entry phone 1, #21

- #26 for entry phone 2, #31 - #36 for entry phone 3, and #41 - #46 for entry phone 4. Up to 6 master keyless entry codes may be

from 4 to 6 digits in length and are stored in locations #51 - #56. The master keyless entry codes can be used at any entry phone.

To change any of the keyless entry codes to one time use, insert a  in front of the specific memory location during programming

(ie: “#11”). To clear any keyless entry codes, simply enter the location number (ie: “#11” or “#11”) without any previous digits.

G. Door Strike Activation Time

A single pole double throw relay is available for each entry phone (a second set of contacts are available on solder pads only), and

each may be programmed with its own “doorstrike” activation time (programmed in seconds). Each time must be 2 digits (Example:

00 = 1/2 sec.) and is stored in locations #19, #29, #39 and #49 for relays 1 through 4 respectively. All activation times are factory

set to 00 (1/2 sec.) Note: A buzz sound will be heard in the house phone and entry phone, indicating the door strike relay has been

activated and visitors can now open the door.

H. Caller ID

The C-2000A is factory set to send “Caller ID” and “Call Waiting Caller ID” information from the entry phones. If “Caller ID” is not

required, enter “2” while in programming to disable the C-2000A from sending “Caller ID” and “Call Waiting Caller ID” data to the

house phones. Enter “1” to enable “Caller ID” and “Call Waiting Caller ID” data (see Operation section A).

I. Entry Phone Ring Cadence

Entry phone calls are factory set to ring the house phones in a custom double ring cadence (.7 seconds on/.3 seconds off/.7 sec-

onds on then 4 seconds off between rings), “3”. The C-2000A can be programmed to give a standard ring cadence for entry phone

calls (2 seconds of ring, and 4 seconds off between rings), enter “4” when in programming. Entry phone ringing can also be dis-

abled by entering “0#62”. This is useful when connecting the C-2000A to the SLP-1 to provide unique front and back door chimes.

J. Outside Line Access

1. Dial “9” to Access the Outside Line - To program the C-2000A for C.O. dial tone, enter “5” while programming. To gain access

to C.O. dial tone, dial a Touch Tone “9”.

2. Instant Outside Line Access (factory default) - To program the C-2000A for private dial tone, enter “6” while programming.

House phones will instantly have the outside line dial tone on an off-hook.

K. Maximum Entry Phone Ring Count

The number of times an entry phone call will ring the house phones can be limited in programming. The programmable maximum

ring count must be 2 digits and is stored in location “#61”. The maximum ring count is programmable from 1 - 99 and factory set to

(05) 5 rings.

VIKING

MODEL C-2000A

VIKING

ELECTRONICS

HUDSON, WI 54016

ADVANCED DOOR/GATE AND

ENTRY PHONE CONTROLLER

1 2 3 4 5

8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

PWR 13.8 VAC

EARTH GND

ENTRY PHONE 1

DOOR STRIKE 1

ENTRY PHONE 2

DOOR STRIKE 2

ENTRY PHONE 3

DOOR STRIKE 3

ENTRY PHONE 4

DOOR STRIKE 4

DOORBELL SWITCH /

AUX. INPUT

AUX. CONTACT

OUTPUT

PHONE LINE

INPUT

LINE OUT

TO PHONES

DIP Switches shown

in the factory default

positions

OFF ON

1 2 3 4

Switch

D. Dip Switch Programming

Position

OFF

Description

Auxiliary Contact Mode

Doorbell Mode (factory setting)

Normal Operation Mode (factory setting)

Security Code Bypass Mode

* Entry Phone automatic disconnect (CPC) disabled

Entry Phone automatic disconnect (CPC) enabled

(factory setting)

Entry Phone busy signal disabled

Entry Phone busy signal enabled (factory setting)

* Note: Viking handsfree entry phones require CPC for faster automatic disconnect.

1 2 3 4 5 6 7 8

Komentarze do niniejszej Instrukcji

Brak uwag

Viking HID-2 Dokumentacja Strona 6

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Viking HID-2

Související produkty a manuály pro Mikrofony Bowers-wilkins ASW2000