Viking K-1900-8 Dokumentacja Pobierz pdf (Strona 3)

Power LED

Doorstrike Buzz

Volume Control

Doorstrike LED

C. Optional LOG BUS Wiring

a. Connect the LINE IN port to a C.O. line or analog PABX/KSU station.

b. From a touch tone phone, call the line connected to the K-1900-3.

c. When the K-1900-3 answers, enter “

Q” followed by the six digit security code, factory set to 845464 (see section B

below). A double beep will indicate that programming has been entered.

d. Program as shown in sections B - G.

e. To exit programming, enter “##7” or do not enter any touch tones for approximately 20 seconds. Three beeps will be

heard, followed by an automatic disconnect.

A. Accessing the Programming Mode

1. Remote Programming

a. Take the phone connected to the PHONE port off-hook.

b. Enter a “Q” followed by the six digit security code, factory set to 845464 (see section B below). A double beep will indicate

that programming has been entered.

c. Program as shown in section B - G.

d. To exit programming, simply hang up the entry phone (push the “Call” button on the K-1700-3).

2. Local Programming Using the Security Code (from entry phone)

a. Move dip switch 1 switch to the ON position (see right).

b. Take the phone connected to the PHONE port off-hook. A double

beep will indicate that programming has been entered.

c. Program as shown in section B - G.

d. When finished, dip switch 1 must be placed back in the OFF

position for normal operation (see right).

e. To exit programming, simply hang up the entry phone

(push the “Call” button on the K-1700-3).

DB-9

(not included)

H Brown (Receive Data)

L Yellow (Signal Ground)

1610m (5280 ft - 1 mile) maximum

run length using 24 gauge wire

Pin 2

(Receive Data)

Pin 5

(Signal Ground)

VIKING

MODEL K-1900-3

POWER 13.8V AC

APARTMENT ENTRY

SYSTEM

VIKING

ELECTRONICS

HUDSON, WI 54016

LINE IN PHONE

123456789

PROGRAM

LOG BUS

AUXILARY

TRIGGER INPUT

RELAY 1A

CONTACTS

RELAY 1B

CONTACTS

N.O.

N.C.

COM.

N.O.

N.C.

COM.

The K-1900-3 transmits 1200 baud

ASCII data from the LOG BUS screw

terminals. Log Bus data is sent each

time there is an entry point event,

and includes the tenant memory

location number dialed and whether

the guest was allowed to enter, or

the keyless entry code dialed and

whether it was valid or not.

If the RS-232 input of a PC, printer, etc. is capable of receiving TTL level RS-232

signals, then the LOG BUS can be wired directly into the RS-232 “Receive Data”

and “Signal Ground” pins to receive ASCII data. Windows “Hyper-Terminal” can be

used to receive the data on a PC (use the settings in the chart to the left) or visit

www.vikingelectronics.com to download free ENTRY LOGGER software (see

Operation section E, “Entry Logger Software”).

Communication Software Configuration

Com

Baud Rate

Data Bits

Stop Bits

Parity

Flow Control

Your serial port (1-4)

1200

none

3. Local Programming Without the Security Code (from entry phone)

B. Controls and Indicators

OFF

VIKING

MODEL K-1900-3

POWER 13.8V AC

APARTMENT ENTRY

SYSTEM

VIKING

ELECTRONICS

HUDSON, WI 54016

LINE IN PHONE

123456789

PROGRAM

LOG BUS

AUXILARY

TRIGGER INPUT

RELAY 1A

CONTACTS

RELAY 1B

CONTACTS

N.O.

N.C.

COM.

N.O.

N.C.

COM.

1 2 3 4 5 6 7 8

Komentarze do niniejszej Instrukcji

Brak uwag

Viking K-1900-8 Dokumentacja Strona 3

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Viking K-1900-8