Viking K-1900-8 Dokumentacja Strona 4
- Strona / 4
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
DOD# 362 ZF301770 Rev DPrinted in the U.S.A.
P
P
r
r
o
o
d
d
u
u
c
c
t
t
S
S
u
u
p
p
p
p
o
o
r
r
t
t
L
L
i
i
n
n
e
e
.
.
.
.
.
.
7
7
1
1
5
5
.
.
3
3
8
8
6
6
.
.
8
8
6
6
6
6
6
6
F
F
a
a
x
x
B
B
a
a
c
c
k
k
L
L
i
i
n
n
e
e
.
.
.
.
.
.
7
7
1
1
5
5
.
.
3
3
8
8
6
6
.
.
4
4
3
3
4
4
5
5
The K-1900-8 is programmed to hang-up if it detects Touch Tones it did not generate (except when in Dumb Phone mode). This
helps prevent toll fraud from hand held dialers. To set the K-1900-8 to block/allow dialing from external devices, access the
Programming mode as shown in section B, then choose block or allow. To Block hand held dialers, enter ,3. To Allow Touch Tones
from external devices, enter ,4.
G. Pre-Dial Pause
In the single number auto-dialer mode, the time from when the handset is taken off-hook until the K-1900-8 auto-dials can be pro-
grammed. Access the Programming mode (section B), then choose a pause length. To set the pause length to Normal (approxi-
mately 1.4 seconds), enter ,5. To set the pause length to Short (approximately 800ms) enter ,6.
F. Hand Held Pocket Dialers
H. Pauses in the Dialing String
To set pauses in the dialing string, access the Programming mode as shown in section B, then enter ,7 to put a 4 second pause
anywhere in the dialing string.
I. Toll Restriction
When the K-1900-8 is in the Standard (Dumb) phone mode, some limited toll restriction is available. With toll restriction enabled, the
phone will hang-up if a 0 or 1 is entered as the first digit, or if more than ten digits are entered. Access the Programming mode (sec-
tion B), then choose enable or disable toll restriction. To set the K-1900-8 to Disable toll restriction, enter ,9. To set the K-1900-8
to Enable toll restriction, enter ,0.
These examples would be entered after accessing the Programming mode as shown in section B.
K. Programming Examples
To Program the K-1900-8 to...
...Touch Tone dial 555-1234
...pulse dial 555-1234 followed by a Touch Tone 9
...dial 9, a 4 second pause and then 555-1234
...set the dialing speed to fast
...clear the speed dial number (dumb phone mode)
Enter Digits
5551234
,8 5551234 ,8 9
9 , 7 5551234
,2
Enter Location
#00
#00
#00
#00
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
A. Single Number Auto Dialer
In the single number auto dialer mode (see Programming section D), when the K-1900-8 is taken off-hook it will speed dial the
phone number programmed in memory location #00. After speed dialing is complete, the keypad is available for user Touch Tone
signaling. In this mode, the K-1900-8 can be programmed to block hand held dialers (see Programming section F).
B. Standard (Dumb) Phone Mode
If nothing is programmed in memory locations #00, the K-1900-8 drops into the dumb phone mode. The phone will act like any
standard 2500 type telephone. The only feature which may be enabled is the limited toll restriction (see Programming section I).
C. Multi-Number Auto Dialer
In the multi-number auto dialer mode (see Programming section D), when the K-1900-8 is taken off-hook it will dial one of six speed
dial numbers programmed in memory locations #01, #02, #03, #04, #05 and #00 when the user presses 1, 2, 3, 4, 5, or 0 (respec-
tively) on the keypad. After speed dialing is complete, the keypad is available for user Touch Tone signaling. In this mode, the K-
1900-8 can be programmed to block hand held pocket dialers (see Programming section F).
J. DIP Switch Programming
Switch
1
1
2
2
Position
ON
OFF
ON
OFF
Description
Learn Mode
Normal Operation (factory setting)
Multi-Number Dialer Mode
Normal Operation (factory setting)
OFF ON
1
2
ON
DIP
Switches
Internal View of
the K-1900-8-EWP
ON
OFF
1
2
ON
DIP
Switches
Internal View of
the K-1900-8
D. Handset Receiver Volume Adjustment
The K-1900-8 has a sealed push button switch located on the inside handle of the handset. Each push of the button will increase
the receiver volume by approximately 5dB. After three actuations, the receiver is at its highest volume setting, a fourth actuation will
bring the volume back to its lowest setting. Hanging up the phone will automatically set the receiver volume to its lowest setting.
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Viking K-1900-8
(4 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji