Viking ES-3 Instrukcja Obsługi Pobierz pdf (Strona 2)

Installation

Definitions

A. Basic Wiring

IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC

outlet and the telephone line. It is recommended that a surge protector be installed to protect against such surges.

26 Bit Wiegand Format: The industry standard data output of access control card readers.

Bi-Directional Access: Two Wiegand devices can be wired in parallel to one ES-1 to control access in both directions

at a single entry point. Simply place one card reader on each side of the door or gate. When either one detects a valid

code, the ES-1 will strike the door. Data logging will not be able to distinguish the direction of the access. If that is a

requirement, two separate ES-1s will need to be installed, so each one can log separate access events from each

side of the door.

Card Plus Keypad Mode: This is a higher security mode in which a valid card + a valid keypad entry is required to

gain access.

Entry Code: The number that when it matches either a Keyless Entry or a Proximity Card number, allows access.

Each tenant may have their own unique Entry Code that is easily changed or removed when a tenant moves out.

Entry Point: A door or gate allowing access into a secure or controlled area.

Facility Code: A 3-digit number that each proximity card contains in order to provide greater security. Usually the

cards used at a given building all have the same facility code.

Keyless Entry: A way for tenants to let themselves in, by entering their entry code on a keypad.

LOG BUS: A two wire data bus that can be wired in parallel with additional ES-1 log busses. Data is sent as 1200

baud ASCII characters at TTL levels (0-5 Volt). Any RS-232 port designed to receive TTL levels can receive log bus

data directly on the “Receive Data” and “Signal Ground” pins.

Memory Location: The number used when programming, that stores the location of an entry code.

One Time Code: An entry code that can only be used once - this feature is handy for visitors. Once the code is used

the ES-1 forgets it.

Proximity Card: A credit size card that identifies itself when within close proximity of a reader. Card “swiping” is not

necessary. The card contains a 3 digit Facility Code, a 5 digit Internal Card number and a 5 digit External Printed

number, that may or may not match the Internal number.

Proximity Card Reader: A device used to read the data from a Proximity Card when its held within a few inches of

the reader.

* Note: Maximum Wiegand run length is 600 feet using 24 gauge wire when using the Viking model PRX-1 proximity

card reader, 500 feet for the PRX-2 keypad/proximity card reader, 800 feet for the PRX-3 (using 3 wire pairs for pwr)

and 2000 feet for the PRX-4 keypad. Run length is reduced to half if two share the same wire run from the same C-

4000 entry point. Run length will also be reduced if using a Wiegand device other than the Viking model PRX-1, that

requires more than 35mA average operating current. Run lengths can be doubled by doubling up on the BLACK and

RED 24 gauge wire, or using 21 gauge (or larger) wire. Certain electrically noisy locations might require shielded wire.

A basic door access controlled entry point is wired as shown below. The relay can be connected as either Normally

Open, or Normally Closed. All 26-bit Wiegand devices are fully supported (power and data) from the ES-1 and

can be installed up to 500 feet away using 24 gauge wire. Viking Wiegand devices can run even further (see Note

above). The ES-1 can support either a card reader (Viking model PRX-1 or PRX-3), keyless entry keypad/proximity

card reader (Viking model PRX-2) or a keyless entry keypad (Viking model PRX-4), or both. If both are installed,

the “Card Plus Keypad” mode can be used. If any two Wiegand devices are used, one can be placed on each

side of a doorway/gate for bi-directional (entry and exit) access control.

Doorstrike

Power Supply

12-24V AC or DC

Doorstrike

12V DC

Adapter

(included)

Share power with 12-24V

AC/DC doorstrike with 200mA

available current or use the

included 12V DC adapter.

Touch Tone

Programming Phone

(not included)

RAD-1A Remote Access

Device (not included,

see DOD# 410)

Remote Touch Tone

Programming Phone

(not included)

- or -

* 610m (2000 ft) max

* 183m (600 ft) max

* 152m (500 ft) max

Viking PRX-1

(not included

DOD# 221)

Viking PRX-2

(not included

DOD# 219)

Viking HID-2

(not included

DOD# 199)

OROR

VIKING©

VIKING

ELECTRONICS

HUDSON,

54016

STAND ALONE

DOOR CONTROLLER

ENTRY SYSTEM

POWER 12V DC

MODEL ES-1

POWER

PROGRAM

PHONE

LOG

BUS

2345

GANG

PROG

6789

WIEGAND

DEVICE

10 11

DOOR

STRIKE

N.O.

COM

N.C.

BLK

RED

GRN

WHT

1 2 3 4 5 6 7 8

Komentarze do niniejszej Instrukcji

Brak uwag

Viking ES-3 Instrukcja Obsługi Strona 2

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Kontrolery drzwi antywłamaniowych Viking ES-3